How_to_Estimate_Current_Drive_Strength_For_OCT
上传者:丁崇生|上传时间:2015-05-07|密次下载
How_to_Estimate_Current_Drive_Strength_For_OCT
如何评估电流驱动强度
How-To Estimate Current Drive Strength for OCT
Introduction. Many Altera® FPGAs have output pin configuration options which allow you to select either a current drive strength or series on chip termination (OCT). Although these have different settings in the Quartus® II software, they use the same structures in the output buffer to implement the desired setting.
This How-To document describes how you can use IBIS models to estimate the current strength of the series OCT settings.
1. Set Up
内容需要下载文档才能查看
The examples in this document use the following:
内容需要下载文档才能查看
Stratix® IV device IBIS models version 2.0
HyperLynx Visual IBIS Editor Version 4.0
2. Current Drive Strength and Series OCT
The output buffers consist of pull up and pull down transistors. As you select higher drive
strengths for your output and bidirectional pins in the Quartus II software, more pull up and pull down transistors are enabled in the output buffer. As the drive strength increases, the output impedance of the output buffer decreases. High current drive strength settings have a lower output impedance than low current drive strength settings.
When using series OCT, a combination of pull up and pull down transistors are enabled to provide the desired output impedance. For non-calibrated series OCT, this is a setting
determined by Altera during device characterization. The non-calibrated OCT setting has a variation over process, voltage, and temperature, and this variance is provided in the respective device Datasheet. Calibrated series OCT will compare the output impedance of the output buffer with the resistance applied to the RUP and RDN pins, and dynamically enables and disables the pull up and pull down transistors until the output impedance of the buffer matches the impedance sensed on the RUP and RDN pins.
As a designer, you may want to know the approximate current drive strength when you select series OCT for output and bidirectional pins. You can use IBIS models and any IBIS viewer to generate IV curves.
3. IV Curves
The following example will show how to estimate the current drive strength of a Stratix IV device
2.5V output buffer configured for 50 ohm non-calibrated OCT located on a row I/O bank (left or right side of the device).
First, view the IV curve of the cmos25_rio_r50 model, this is the 50 ohm series non-calibrated OCT model for a 2.5V standard. In this example, the Pulldown curve will be used. (Note, Altera IBIS models use either “cmos” or “ttl” for I/O standards at or below 3.0V. The terms are
interchangeable. See Knowledge Database Solution for further information.
Page 1 of 6
如何评估电流驱动强度
内容需要下载文档才能查看
Figure 3-1. 2.5V row I/O IV curve using series 50 ohm OCT
Next you will need to create IV curves for the current drive strength settings that can be applied to the 2.5V I/O standard. In Stratix IV devices, the row I/O pins support current drive strength settings of 4, 8, and 12ma. You will find the OCT setting will either closely match one of the current drive strength settings, or the curves will fall in between two different current drive strength settings.
When comparing IV curves, you should select a voltage point on the IV curve and compare the current value at that same voltage point for each IV curve. In this example, we will compare the current at 0.7V in each IV curve. This is the Vin low maximum switching threshold for 2.5V I/O standards. This example compares the pulldown IV curves which represent the characteristics of an output buffer as it switches from driving a logic high to driving a logic low.
Note, the current drive strength setting of the output buffer is not the maximum strength it will drive. The current drive strength setting is a minimum specification for the strength of current at the voltage switching threshold for the respective I/O standard.
Page 2 of 6
如何评估电流驱动强度
内容需要下载文档才能查看
Figure 3-2. 2.5V row I/O IV curve using a current drive strength of 4ma
By comparing figures 3-1 and 3-2, it is easy to see the current drive strength of the 50 ohm OCT setting is higher than the 4mA setting.
The 50 ohm OCT “typical” IV curve has 21.8mA at 0.7V, and the 4mA “typical” IV curve has 11.9mA at 0.7V.
Page 3 of 6
如何评估电流驱动强度
内容需要下载文档才能查看
Figure 3-3. 2.5V row I/O IV curve using a current drive strength of 8ma
By comparing figures 3-1 and 3-3, the current drive strength of the 50 ohm OCT setting is still higher than the 8mA setting.
The 50 ohm OCT “typical” IV curve has 21.8mA at 0.7V, and the 8mA “typical” IV curve has 18.1mA at 0.7V.
Page 4 of 6
如何评估电流驱动强度
内容需要下载文档才能查看
Figure 3-4. 2.5V row I/O IV curve using a current drive strength of 12ma
By comparing figures 3-1 and 3-4, the current drive strength of the 50 ohm OCT setting is less than the 12mA setting.
The 50 ohm OCT “typical” IV curve has 21.8mA at 0.7V, and the 12mA “typical” IV curve has 28.0mA at 0.7V.
4. Conclusion
By comparing the IV curves for each output buffer configuration using 2.5V, the current drive strength of the 50 ohm series OCT configuration is between 8mA and 12mA. When comparing the data points at the same place on the curve, the 50 ohm series OCT setting appears to be below the mid-point between the 8mA and 12mA current drive strength settings. Thus you can estimate the current drive strength to be approximately 9 to 10mA.
Page 5 of 6
下载文档
热门试卷
- 2016年四川省内江市中考化学试卷
- 广西钦州市高新区2017届高三11月月考政治试卷
- 浙江省湖州市2016-2017学年高一上学期期中考试政治试卷
- 浙江省湖州市2016-2017学年高二上学期期中考试政治试卷
- 辽宁省铁岭市协作体2017届高三上学期第三次联考政治试卷
- 广西钦州市钦州港区2016-2017学年高二11月月考政治试卷
- 广西钦州市钦州港区2017届高三11月月考政治试卷
- 广西钦州市钦州港区2016-2017学年高一11月月考政治试卷
- 广西钦州市高新区2016-2017学年高二11月月考政治试卷
- 广西钦州市高新区2016-2017学年高一11月月考政治试卷
- 山东省滨州市三校2017届第一学期阶段测试初三英语试题
- 四川省成都七中2017届高三一诊模拟考试文科综合试卷
- 2017届普通高等学校招生全国统一考试模拟试题(附答案)
- 重庆市永川中学高2017级上期12月月考语文试题
- 江西宜春三中2017届高三第一学期第二次月考文科综合试题
- 内蒙古赤峰二中2017届高三上学期第三次月考英语试题
- 2017年六年级(上)数学期末考试卷
- 2017人教版小学英语三年级上期末笔试题
- 江苏省常州西藏民族中学2016-2017学年九年级思想品德第一学期第二次阶段测试试卷
- 重庆市九龙坡区七校2016-2017学年上期八年级素质测查(二)语文学科试题卷
- 江苏省无锡市钱桥中学2016年12月八年级语文阶段性测试卷
- 江苏省无锡市钱桥中学2016-2017学年七年级英语12月阶段检测试卷
- 山东省邹城市第八中学2016-2017学年八年级12月物理第4章试题(无答案)
- 【人教版】河北省2015-2016学年度九年级上期末语文试题卷(附答案)
- 四川省简阳市阳安中学2016年12月高二月考英语试卷
- 四川省成都龙泉中学高三上学期2016年12月月考试题文科综合能力测试
- 安徽省滁州中学2016—2017学年度第一学期12月月考高三英语试卷
- 山东省武城县第二中学2016.12高一年级上学期第二次月考历史试题(必修一第四、五单元)
- 福建省四地六校联考2016-2017学年上学期第三次月考高三化学试卷
- 甘肃省武威第二十三中学2016—2017学年度八年级第一学期12月月考生物试卷
网友关注
- 2019北京公务员考试行测题库:行测每日一练练习题(11)
- 北京公务员考试面试题库:面试结构化面试模拟题
- 2018北京市公务员考试面试试题(3月11日上午)
- 2018北京市公务员考试面试试题(3月7日上午)
- 2019北京公务员考试申论每周一练:我们都欠中国医生一个道歉
- 2018北京公务员考试行测试题——常识判断十八(多选题)
- 北京公务员考试面试题库:面试结构化面试模拟题答案(1)
- 2019北京公务员考试行测题库:行测判断推理练习题(3)
- 北京公务员考试面试题库:面试结构化面试模拟题答案
- 2018北京公务员考试行测试题——常识判断(六)
- 2018北京公务员面试题库:面试结构化面试模拟题答案(11)
- 2018北京市公务员考试面试试题(3月7日下午)
- 2019北京公务员考试申论每周一练答案:我们都欠中国医生一个道歉
- 2018北京公务员考试行测试题——常识判断(五)
- 2019北京公务员考试申论:农民贷款难现象
- 2018北京公务员考试行测试题——常识判断十三(多选题)
- 北京公务员考试面试题库:面试结构化面试模拟题(2)
- 2019北京公务员考试申论答案:农民贷款难现象
- 2018北京公务员考试行测试题——常识判断(四)
- 2018北京公务员考试行测试题——常识判断十五(多选题)
- 2018北京公务员面试题库:面试结构化面试模拟题(12)
- 2018北京市公务员考试面试试题(3月8日下午)
- 2018北京公务员面试题库:面试每日一练结构化面试模拟题答案(10)
- 2019北京公务员考试行测题库:行测判断推理练习题答案(3)
- 2018北京市公务员考试面试试题(3月8日上午)
- 2018北京公务员考试行测试题——常识判断十七(多选题)
- 2019北京公务员考试申论:恶搞历史和经典现象
- 2018北京公务员考试行测试题答案及解析
- 2018北京公务员面试题库:面试每日一练结构化面试模拟题(10)
- 2018北京公务员考试行测试题——常识判断十(多选题)
网友关注视频
- 沪教版牛津小学英语(深圳用) 四年级下册 Unit 4
- 8.练习八_第一课时(特等奖)(苏教版三年级上册)_T142692
- 苏教版二年级下册数学《认识东、南、西、北》
- 人教版历史八年级下册第一课《中华人民共和国成立》
- 北师大版数学 四年级下册 第三单元 第二节 小数点搬家
- 七年级英语下册 上海牛津版 Unit3
- 第五单元 民族艺术的瑰宝_16. 形形色色的民族乐器_第一课时(岭南版六年级上册)_T1406126
- 【获奖】科粤版初三九年级化学下册第七章7.3浓稀的表示
- 【部编】人教版语文七年级下册《老山界》优质课教学视频+PPT课件+教案,安徽省
- 沪教版牛津小学英语(深圳用) 四年级下册 Unit 3
- 北师大版小学数学四年级下册第15课小数乘小数一
- 北师大版数学四年级下册第三单元第四节街心广场
- 六年级英语下册上海牛津版教材讲解 U1单词
- 外研版英语七年级下册module3 unit2第一课时
- 外研版英语七年级下册module3 unit2第二课时
- 冀教版小学数学二年级下册第二周第2课时《我们的测量》宝丰街小学庞志荣.mp4
- 沪教版牛津小学英语(深圳用) 四年级下册 Unit 8
- 第五单元 民族艺术的瑰宝_15. 多姿多彩的民族服饰_第二课时(市一等奖)(岭南版六年级上册)_T129830
- 冀教版小学数学二年级下册第二单元《余数和除数的关系》
- 北师大版数学四年级下册3.4包装
- 冀教版英语四年级下册第二课
- 每天日常投篮练习第一天森哥打卡上脚 Nike PG 2 如何调整运球跳投手感?
- 小学英语单词
- 沪教版牛津小学英语(深圳用) 四年级下册 Unit 7
- 北师大版八年级物理下册 第六章 常见的光学仪器(二)探究凸透镜成像的规律
- 沪教版牛津小学英语(深圳用) 五年级下册 Unit 10
- 苏科版数学 八年级下册 第八章第二节 可能性的大小
- 沪教版八年级下册数学练习册21.3(3)分式方程P17
- 冀教版小学英语五年级下册lesson2教学视频(2)
- 第五单元 民族艺术的瑰宝_16. 形形色色的民族乐器_第一课时(岭南版六年级上册)_T3751175
精品推荐
- 2016-2017学年高一语文人教版必修一+模块学业水平检测试题(含答案)
- 广西钦州市高新区2017届高三11月月考政治试卷
- 浙江省湖州市2016-2017学年高一上学期期中考试政治试卷
- 浙江省湖州市2016-2017学年高二上学期期中考试政治试卷
- 辽宁省铁岭市协作体2017届高三上学期第三次联考政治试卷
- 广西钦州市钦州港区2016-2017学年高二11月月考政治试卷
- 广西钦州市钦州港区2017届高三11月月考政治试卷
- 广西钦州市钦州港区2016-2017学年高一11月月考政治试卷
- 广西钦州市高新区2016-2017学年高二11月月考政治试卷
- 广西钦州市高新区2016-2017学年高一11月月考政治试卷
分类导航
- 互联网
- 电脑基础知识
- 计算机软件及应用
- 计算机硬件及网络
- 计算机应用/办公自动化
- .NET
- 数据结构与算法
- Java
- SEO
- C/C++资料
- linux/Unix相关
- 手机开发
- UML理论/建模
- 并行计算/云计算
- 嵌入式开发
- windows相关
- 软件工程
- 管理信息系统
- 开发文档
- 图形图像
- 网络与通信
- 网络信息安全
- 电子支付
- Labview
- matlab
- 网络资源
- Python
- Delphi/Perl
- 评测
- Flash/Flex
- CSS/Script
- 计算机原理
- PHP资料
- 数据挖掘与模式识别
- Web服务
- 数据库
- Visual Basic
- 电子商务
- 服务器
- 搜索引擎优化
- 存储
- 架构
- 行业软件
- 人工智能
- 计算机辅助设计
- 多媒体
- 软件测试
- 计算机硬件与维护
- 网站策划/UE
- 网页设计/UI
- 网吧管理