小熊玩具折纸教程

内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看

1.With darker side up, form2.Swing back.rabbit ears on both sides.

4.Valley down.5.Unfold.

7.Asymmetrical squash.8.Squash.

3.Valley up.

6.Repeat steps 3-5 in mirrorimage.

9.Pull out single layer to makesymetrical.

内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看

11.Valley up.14.Pull one layer through.squash to form at bottom.

17.Swing down.20.Squash.formation.

12.Precrease.

15.Valley folds.

18.Open out top.

21.Sink halfway.

10.Squash.13.Form valley fold, allowing16.Turn over.19.Collapse into rabbit-ear

内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看

22.Swing over.25.Sink triangularly.28.Precrease flap halfway.

31.Swing over flap A, whileincorporating a reverse fold.A gusset will form where flapA meets the point.

23.Petal up.26.Swing down.29.Valley along precrease.

32.Pull up the thick set of layers

24.Swing up.

27.Valley outwards.

30.Valley down point, whileswinging out top single layer.

33.Pull up edge B, so that it isparallel with the base ofmodel.

内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看

34.Repeat steps 22-33 on theother side.

37.Valley up.

40.Swing over. Repeat steps36-40 on other side, skippingstep 38.

43.Reverse fold.

35. Valley. Rotate model.38.Mountain fold the single layerto match up with folded edgeabove.

41.Repeat steps 3-5 on the topflap.44.Pull around single layer fromunderneath.

1/2

36.Squash.

39.Pull out single layer fromunderneath.

42.Top shown only. Fold in half,while outside reverse folding.

45.Repeat step 44 behind (it iseasier to first swing the smallflap to the other side toaccomplish this).

内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看 内容需要下载文档才能查看

46.Swing one flap over.

49.Swing over.

52.Mountain edge of ear tomake it symetrical. Repeatsteps 49-52 on other side.

55.Pull single layer to surface(closed sink).

47.Valley up; see next step for48.Note that points A and B arepositioning.

on the same plane. Swingover.

50.Fold out top edges a small51.Swing over head whileamount, allowing tip toswiveling out the ear. Formsquash.

mountan fold first. Center ofear should lie at 45 angle.

53.Turn over.

54.Fold sides in. Pull out tinyflap from bottom pocket.

56.Stretch the bottom upwards.57.Swivel the material from the

Valley the lower edges of thelegs behind.

leds to the center.